Merchandise Description:
DC motor is a rotating motor that can change DC electrical vitality into mechanical power (DC motor) or mechanical power into DC electric powered vitality (DC generator). It is a motor that can transform DC and mechanical strength into one an additional. When it operates as a motor, it is a direct current motor, which converts electrical vitality into mechanical power when it operates as a generator, it is a direct present generator, which converts mechanical energy into electrical power.
| Solution Name | Z4 Sequence 60kw Medium DC Motor |
| Motor Type | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition framework | The construction of DC motor should consist of two components: stator and rotor. The static component of DC motor is called stator. The primary operate of stator is to make magnetic subject, which is composed of foundation, major magnetic pole, commutation pole, stop cap, bearing and brush gadget. Operating component is known as rotor, whose principal function is to produce electromagnetic torque and inductive electromotive pressure. It is the hub of strength conversion of DC motor. So it is also typically referred to as armature, which is made up of rotor, armature main, armature winding, commutator and admirer. |
| Model | Z Variety |
| Seat quantity | Z315-Z1000 |
| electricity | sixty~2800kW |
| Voltage | 220~1000V |
| Torque range | 1.five ~180kNm |
| Security stage | IP23, IP44 |
| Cooling mode | IC06,IC17,IC37,IC81W |
| Working speed | Constant Pace /Low Speed /Alter Pace /Large Speed Other |
| Major classification | DC Motor is a machine that converts mechanical energy into DC power. It is primarily used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation power source of alternator. Even though in locations where DC electrical power is needed, AC energy rectifier is also employed to convert AC into DC energy, but from some elements of performance, AC rectifier electrical power source can not totally replace DC generator. |
| Application | DC motors are commonly employed in tape recorders, movie recorders, online video discs, electrical shavers, hair dryers, electronic watches, toys and so on. |
| Upkeep technique | Expert motor servicing middle motor servicing method: cleansing stator and rotor – changing carbon brush or other areas – vacuum F force dipping paint – drying – Calibration equilibrium. one. Use environment should be always dry, motor area ought to be retained cleanse, air intake ought to not be hindered by dust, fibers and other obstructions. two. When the thermal defense of the motor continues to run, it should be ascertained whether the fault arrives from the motor or the overload or the placing value of the protective system is way too minimal. Following eliminating the fault, it can be place into operation. three, guarantee that the motor is nicely lubricated throughout operation. The standard motor operates for about 5000 hrs, that is to say, lubricating grease must be added or replaced. When bearing overheating or lubricating deterioration is found in procedure, the hydraulic stress need to change lubricating grease in time. When replacing grease, the previous grease need to be eliminated, and the oil groove of bearing and bearing include ought to be washed with gasoline. Then ZL-3 lithium grease ought to be stuffed with one/two (2 poles) and two/three (4 poles, 6 poles and eight poles) of the cavity among the inner and outer rings of the bearing. four. When the existence of the bearing is over, the vibration and sounds of the motor will increase clearly. When the radial clearance of the bearing reaches the following value, the bearing need to be replaced. five, when getting rid of the motor, it is Alright to take away the rotor from the shaft extension or the non extension finish. If it is not needed to unload the fan, it is much more hassle-free to just take out the rotor from the non-axle extension conclude. When pulling out the rotor from the stator, the stator winding or insulation must be prevented from getting broken. 6. When changing the windings, the type, dimensions, turns and gauges of the first windings need to be recorded. When these information are missing, they must be obtained from the producer and the unique designed windings ought to be altered at will, which frequently deteriorates one particular or a number of functionality of the motor or even makes it unattainable to use them. |
