DAWSON CZPT & MOULD Group
***EXTRUSION BLOW MOLDING Equipment Expert***
Our buyers are all around the world.
Vietnam, Australia, Indonesia, Malaysia, Thailand, Sri Lanka, Kazakhstan, Russia, UAE, Saudi Arabia, Malta, Romania, Italy, India, Syria, Ethiopia, Egypt, Sudan, Tunisia, Algeria, Kenya, Nigeria, South Africa, Zimbabwe, Mexico, Guatemala, Ecuador, Colombia, Venezuela, Peru….
Accumulation kind blow molding equipment ABLD100
Appropriate for making a hundred-250L HDPE Lifestyle buoy, floater…
Equiped with MOOG parison controller
with SERVO Motor
Extrusion blow molding device ABLD100
| extruder | |||
| one | Screw diameter | 100mm | |
| 2 | L/D ratio | 24:one | |
| three | Screw speed | 15~50r.p.m. | |
| four | Push motor | 45Kw | |
| five | Heating zone with cooling supporter | 6 zone | |
| 6 | Output/Capacity | 170 Kg/hr(HDPE particle) | |
| 8 | Heating potential | 25.1 kw | |
| nine | Vertical adjustment of head | 500mm | |
| ten | Forward/Backward adjustment of head | 500mm | |
| eleven | Groove feed barrel cylinder | Have IKV | |
| twelve | Gear box | Tough gear decelerator | |
| 13 | Ladder and protection rails | Have | |
| Accumulator CZPT | |||
| 1 | Accumulator potential | 20L(15kgHDPE) | |
| 2 | Style | 1st in and first out | |
| 3 | Heating zone | six zone | |
| 4 | Heating potential | 25.1kw | |
| 5 | Max die&pin diameter | 450mm | |
| six | Die head axis with pre-blow | Ø120mm | |
| seven | Accumulator push-out stroke measurement | Transducer Italy Gefran | |
| 8 | Injection strain | 12 Mpa | |
| nine | Extruder end | Have | |
| CLAMPING Unit | |||
| one | Tie bar | Two tie bar | |
| two | Platen measurement | 900(W)X1400(H) | |
| three | Size of mould | 900-960mm | |
| 4 | Clamping drive | 780KN | |
| 5 | Shut/Open up stroke | 880-1700mm | |
| six | Mildew excess weight | Max. 5000 kg | |
| 7 | Clamping stroke measurement | Transducer Italy Gefran | |
| eight | CZPT valve | ZheJiang Hitech | |
| nine | Quantity of hydraulic cylinder | one | |
| 10 | Large pressure | fourteen Mpa | |
| 11 | Support components for platen motion | Liner Xihu (West Lake) Dis. | |
| HYDRAULIC Method | |||
| one | Principal motor/vice motor | AC15Kw/15Kw | |
| two | CZPT valve | ZheJiang Hitech | |
| 3 | CZPT pump | ZheJiang Hitech | |
| 4 | Oil tank capacity | 850L | |
| 5 | Running strain | twelve Mpa | |
| six | Cooling h2o for oil | fixed | |
| seven | Control of oil level | be observed dipstick | |
| PNEUMATIC Program | |||
| 1 | Operating pressure | .8 Mpa | |
| 2 | Blow pressure | .8 Mpa | |
| 3 | Needle blow circuit | Large & lower strain | |
| four | Intermittent blow | Have | |
| five | Managed help air for parison | Have | |
| 6 | Air Valves | AIRTAC | |
| 7 | Fast exhaust for assist air | Have | |
| PARISON Control | |||
| 1 | Programmer | JAPAN MOOG | |
| two | Servo valve | MOOG |
|
| three | Servo cylinder | Intergret of die head | |
| 4 | CZPT pack |
ZheJiang YOSHE Variable Displacement Piston Pumps |
|
| CZPTITY | |||
| 1 | Contactor |
Schneider |
|
| 2 | Complete connected load (approx.) |
114kw/h | |
| 3 | Regular power usage (approx.) |
42 kw/h | |
| Water COOLING | |||
| one | Equipment h2o consumption |
6000L/h | |
| 2 | Mould h2o consumption |
6000L/h | |
| AIR Usage | |||
| one | Compressed air intake | 1.2 kgf/cm2, 3000 L/min | |
| OTHER Attributes | |||
| one | PLC manage | MITSUBISHI | |
| 2 | Xihu (West Lake) Dis.n equipment interface | Hitech | |
| three | Recipe storage in difficult disk | Obtainable | |
| HEATING Management | |||
| one | Energy source to heating aspect | Relay + Contactor | Japan Omron+Korea LG |
| 2 | Control | PLC controle | |
| 3 | Type of thermocouple | K Kind | |
| four | Adjustable lower and upper restrict alarm | Have | |
| five | Cold begin avoidance for screw | Have | |
| six | Alarm for thermocouple and heating component breakage | Have, heating element breakage by anperemeter | |
| 7 | Pre-heating function | Have | |
| Die-ring AND Die-pin | |||
| one | 1 sets of die & pin | 1 established according to consumer | |
| 2 | Test content | Customer offer 300kg content to seller for machine tests | |
| Selection | |||
| 1 | Base blow (hydraulic) and sealing device (pneumatic) | CZPT blow pin (like broaden & up-down & parison seal) | |
| 2 | Robot | Have | |
| three | Machine Dimension | 6.8×3.3×5 | |
| 4 | Complete bodyweight | twenty | |
