|Product||CZPT||Stand-by||stator||Single bearing Packed|
|SWT-184ES||15||19||seventeen||21||135mm||520*490*510||.13||one hundred thirty|
|SWT-224F||fifty eight||seventy three||sixty four||80||240mm||810*490*770||.31||320|
|SWT-224G||sixty eight||eighty five||seventy six||95||300mm||860*490*770||.33||365|
|SWT-274C||eighty||one hundred||88||a hundred and ten||165mm||810*580*850||.40||390|
|SWT-274D||96||one hundred twenty||104||one hundred thirty||205mm||810*580*850||.40||427|
|SWT-274ES||100||125||112||a hundred and forty||215mm||810*580*850||.40||440|
|SWT-274E||112||one hundred forty||124||155||230mm||930*580*850||.46||490|
|SWT-274FS||one hundred twenty||a hundred and fifty||132||one hundred sixty five||250mm||930*580*850||.46||510|
|SWT-274F||128||a hundred and sixty||140||175||285mm||930*580*850||.46||530|
|SWT-274G||146||183||a hundred and sixty||200||335mm||980*580*850||.49||593|
|SWT-274J||one hundred eighty||225||200||250||410mm||1110*585*850||.55||660|
one.Massive Brief circuit capacity increase the capability to start off the motor right.
two. Integral casting machine body enhances the concentricity and mechanical strength.
3. Hassle-free wiring makes it a lot more less difficult to alter the output voltage
4.Far better voltage regulator, so that the generator output voltage is basically stable unchanged.
five.The design of aviation conductive ring make generator run much more effortlessly.
six.2/3 concentric winding distribution way, let the generator voltage waveform distortion is scaled-down.
seven.Easy wiring make windings and parts direct wiring far more affordable and easy.
8.A realistic production procedure and a lot of depth styles make the generator has for a longer time provider life.
Engine casing characteristics
one.One particular-piece body casting improve the mechanical power, and in the approach to ensure good concentricity to improve the machining precision.(The ST STC casing is divided into drive conclude go over, the human body and the non travel end protect assembly, the 3 components can not be processed at the same time, need to be processed individually, therefore, when machining is assembled, machining errors and assembly problems can be produced. The 3 can not achieve concentric, therefore generator in the method of operating easily mechanical resonance, Decreased provider lifestyle, Increase the fee of voltage waveform distortion and electromagnetic sounds.)
2.Enhance the thickness of the body casting, Make the generator operate far more effortlessly, better heat dissipation result.(Such as the ST/STC generator chassis and rear finish protect is straightforward to rupture, Some have not however shipped to the customer and in transit has been damaged, And some to the customer did not use a period of time also broke up.
3. Use TH200 model of solid iron casting base,Much more resistant to corrosion and capable to function in severe environmental problems.(Such as the Stamford generator for skinny plate forming, running in corrosion resistance and severe environment ,after a period of time the shell is straightforward to corrode a lot of holes,Leads to the harm of winding and core factors are exposed.
Conducting ring characteristics:
1. Aviation electric powered conduction ring make operating much more stable,never worry about the Carbon brush very poor speak to any much more, or the carbon brush and the copper ring is worn as well quickly.(these kinds of as the carbon brush and the copper ring of ST/STC generator often poor get in touch with and change,cause the generator does not produce electrical power, the carbon brush and the copper ring is worn too fast, not for a while it has to be changed carbon brush or copper ring.)
2.Conductive ring connector with the lotus kind copper core connector, make routine maintenance a lot more practical and replacement far more more quickly.(The ST/STC to substitute the copper ring, 1st require to dismantle the carbon rod and bearing go over, and next need to take non drive end cap aside, then get rid of bearing, at this timecan eliminate the copper ring, the method is sophisticated, substitute is really troublesome. if the exciter armature of brush-significantly less generator failure, dismantling is quite troublesome, And requirements special tools and expert maintenance staff to replaced.
3.Sealed conductive ring,will not have to observe out for the oil or h2o droplets.(If the ST/STC generator has a little grease adhered to the above, the copper ring will produce a layer of insulation isolation, so that the generator can not produce excitation voltage CZPT making electrical power.)
one. The concentric 2/three winding distribution lowers voltage waveform distortion and increases electricity good quality.
two.Bare portion of the winding spray paint,Can effectively stop dew, corona, anti-corrosion, at the exact same time can increase the winding mechanical strength.
Voltage regulator characteristic:
1.Binary dual route managed voltage regulator,it helps make the generator run far more smoothly,no-load and load voltage variation is not a lot more than two%,Cold and very hot state voltage regulation charge is considerably less than three%.
2.The fixtures of Shockproof regulator improve the earthquake resistance of the regulator.No lengthier have to be concerned about the solder joints thanks to vibration and harm.
one. The design of centrifugal fan has greater air volume, far better warmth dissipation, so the winding insulation is durable.
2. The cast -aluminum thermal sleeve kind of supporter bracket, No for a longer time have to worry about utilizing a long supporter out of rotation.
three.Supporter and enthusiast bracket individual styles make the substitute admirer far more basic.
Employing double sealed bearing, make the bearing service life for a longer time, run far more silent. No lengthier like open bearings that need to have to incorporate grease frequently. This sort of as ST/STC turbines are open bearings, this bearing is simple to grease, bearing beads hurt caused by dry mill in the bearing room.
1. All areas contacted with the wire are wrapped or isolated with specifically made insulation products.
two. All terminals with insert sort, the two terminals inserted into the guiding wire in the insulating sheath,the other two stuck copper wire,so that the finish is not effortless to free from the lead wire and guide wire is not very easily broken thanks to vibration.
3. The mark of terminals is unique, so that every line can be located in the corresponding place on the wiring diagram,and not as connecting the mistaken wire hurt the motor or ingredient.
Δ COMPANY PROFILE
ZheJiang SURIRELLA CZPTAL CZPT CO.,LTD. was set up in 2007, is a professional Alternator and Diesel generator established producer.. All of our merchandise have CE and ISO certifications.
Our motor is largely run by CUMMINS, DEUTZ and so on. In addition to creating generally items, We have new alternator, energy range kind 6kW to 200kW, Stamford new style but much reduced cost and scaled-down size. Only our manufacturing facility can make this alternator in China.
We are considering of “Quality initial, CZPTer leading”,sincerely welcome you to create long-term cooperation with us.
Δ FAQ (FREQUENCY Requested Concern)
Query: What’s your warranty time period?
Solution: Our payment phrases is 1 year
Question: Does your generators has international guarantee?
Reply: Of course, most of our goods like CZPT, Doosan electrical power generator get pleasure from the worldwide guarantee service. And the alternator we use like Leroysomer, Stamford, marathon also appreciate the international guarantee services, so you do not need to be concerned about the aftersales support.
Question: What’s your payment terms?
Reply: We can accept thirty% deposit,70% remaining soon after BL copy
Issue: What’s your delivery time?
Answer: Our standard shipping and delivery time is thirty doing work days. But if your get is some unique engine and alternator, then the shipping and delivery time is for a longer time.